...

Sanitary Pneumatic Butterfly Valve: 6 Specs To Confirm

20/11/2026

Quick takeaways

  • The valve does not set the size ceiling — the actuator does. The stainless pneumatic head stops at DN200, the aluminium ZT head at DN150, the electric HL head at DN200.
  • EFUN builds six end styles, and only one lets you lift the seat out without cutting the pipe.
  • Two inches is two inches until you read the wall. The same 2″ clamp end is 1.45 mm on DS, 1.5 mm on SMS/ISO, 1.65 mm on 3A and 1.725 mm on RJT.
  • “Air to air” is not a fail position. It is the deliberate absence of one, and it needs a stored-air plan.

A sanitary pneumatic butterfly valve takes six lines on an order, not one sentence. Bore, end style, body build, body grade, seat compound and standard settle in that order, because each one narrows the next. Get them right and the valve drops into the line first time. Get one wrong and a pneumatic actuator arrives bolted to a body that will not fit. This guide walks the six specifications in the order a purchase order needs them, then the three actuator decisions that follow, then the wording that stops the mistake repeating.

Sanitary Pneumatic Butterfly Valve: 6 Specs To Confirm

Six specifications decide a pneumatic sanitary butterfly valve, and they carry very different weight. The first four are mechanical: you can read them off a drawing and confirm them with a tape measure. The last two are chemical, and they come off the process. Buyers who start at the seat usually end up re-ordering the body, because no fitting change will fix the seat.

Bore: From The Line To The Model Range

Bore is the specification most buyers get right at the pipe and wrong at the actuator. The body and the head are two separate size maps, and the second one ends sooner.

The butterfly range runs from 1/2″ to 12″, DN10 to DN300, and the flanged pneumatic body goes further still — EFUN lists the DMD-001 pattern from 3/4″ to 24″. A body on its own will not ship as a working valve. What decides the shipment is the head bolted on top of it.

EFUN lists the stainless pneumatic head — Φ85, Φ108 and Φ133 — against DN20 to DN200, or 3/4″ to 6″. The aluminium ZT head covers DN20 to DN150. The electric HL head covers DN20 to DN100 on HL-05 and HL-10, and DN125 to DN200 on HL-20. Beyond DN200 the standard heads run out, and the flanged body moves to the NM series: NM145S at DN250, NM160S at DN300, and NM180S from DN350 up.

Which means a DN300 sanitary butterfly valve exists, and a DN300 pneumatic sanitary butterfly valve also exists — but they are not the same product line. If a drawing says DN250 and the enquiry says “with pneumatic actuator”, the head has to come from the NM family, not from the ZT family. That single sentence is where most quotations go wrong, so bore and actuator are worth confirming together rather than one after the other.

The sanitary butterfly valve range page lists every bore and every head in this article; check it before you commit a line size to a drawing that will be issued for construction.

Body Style: Six Ways To Join The Pipe

EFUN builds six end styles, and a question that has nothing to do with flow decides the choice: who will take this valve out, and how often.

End style How it joins Comes apart in Where it earns its place
Welded Butted and welded to the tube end Cutting the tube CIP circuits, vibration, no joint to clean around
Clamp Two ferrules drawn together by one clamp Under a minute Lines opened weekly for swabs or inspection
Male thread Threaded onto a female port Winding off Instrument and sampling connections
Weld / male One end welded, one threaded Half the joint Transition from a welded header into equipment
Union / male Union nut at one end, thread at the other Winding off, with alignment Short branches that must line up after assembly
Three piece Two flanges clamp the centre section Two flanges off, centre out Seat renewal without cutting the pipe

Read the first five rows together, because they share a consequence: to renew the seat, the valve has to leave the line. The three-piece body is the only one where the centre section comes out between its two flanges and both pipe ends stay exactly where the welder left them. On a line the crew strips and rebuilds every shutdown, that difference is worth more than the price gap between the two bodies.

Below the end style sits a second decision that is easy to skip: welded or clamped is a maintenance policy rather than a preference. A welded joint will not come apart at 2 a.m. to clear a blockage, and a clamp joint will loosen under a pump that hammers — we compare the two in welded versus tri-clamp sanitary butterfly valves if the line is still at the drawing stage.

Sanitary butterfly valve with clamp ends and a multi-position handle

Body Build: Two Piece Or Three Piece

Every body in the range comes from the same stack: two body halves, one disc, a disc gasket, stem bushings and a stem seal, drawn together with bolts and nuts. The three-piece version adds two flanges and two flange gaskets to that stack, and nothing else changes — same disc, same seat, same stem.

What separates the two bodies is where the joint line sits relative to the seat.

On a two-piece body the two halves close directly onto the seat, which makes the shortest, stiffest and cheapest assembly. It is the right body for a line that runs and cleans in place, where the seat should last as long as the valve.

On a three-piece body the seat sits in the centre section, and the two flanges hold that section against the pipe ends. Loosen the flanges and the centre section lifts out with the seat in it. Pay for that when the seat is on a renewal schedule: high-temperature CIP, product with solids that polish the seat edge, or a valve cycled far more often than the rest of the line. It is also the body to specify for a welded line, because a welded line with a two-piece valve has no way to reach the seat without a disc cutter.

The version in the photograph below is the three-piece pattern with a pull handle; the pneumatic version uses the same body and replaces the handle with a bracket and a head.

Three piece sanitary butterfly valve with a blue seat ring and pull handle

Body Material: 304 Or 316L

EFUN stocks two grades: SS304 (1.4301) and SS316L (1.4404). Most buyers choose on price and then justify it on chemistry, so it is worth doing it the other way round.

304 is the correct grade for clean media with no chloride load: milk, beer, sugar syrup, water, and CIP with caustic and nitric acid. It is also the grade most installations actually need, which is why specifying 316L by reflex costs money without buying anything.

316L earns its premium in four situations: a product carrying chloride (brine, whey, some sauces and marinades), a line that sees steam sterilisation often, a pharmaceutical or biotech duty where an auditor will read the material certificate, and any body that will be welded into a spool and not touched again for years. The L matters as much as the 316: low carbon keeps chromium carbide from forming at the weld, which is where a 304 weld in a hot CIP line starts to pit.

Neither grade survives a bad finish. A 316L body with an unground weld is less hygienic than a 304 body with a polished one, and no certificate changes that.

Seat Compound: VMQ, FPM, Or EPDM

EFUN lists three compounds for the seat: VMQ (silicone), FPM (fluoroelastomer) and EPDM. All three will seal, but only one will survive your cleaning cycle.

The 10 bar / 130 °C figure printed for the range is the valve’s rating, not the seat’s. The elastomer reaches its own limit first, and where that limit sits depends on the compound, the medium and the temperature of the caustic — which is why the number has to come from the supplier in writing, for the compound on the order. A supplier who answers “suitable for food” has not answered the question.

The selection logic, in the order to ask it:

  • EPDM is the default for hot water, caustic CIP and steam sterilisation, and it is the compound that most dairy and beverage lines should start from. It is the wrong choice for fats, oils and aromatic solvents.
  • FPM is the compound for fat-rich product, oils and more aggressive chemistry, and it is the one to ask about when a line runs cream, butter or flavoured emulsions.
  • VMQ covers a wide temperature span and clean media, and the one to question hardest when the CIP caustic is strong or the line sees steam, because silicone is the seat that fails quietly.

One line can need two answers. A dairy valve handling hot caustic and a fat-rich product will last a season or five years depending on which exposure is worse, so price is the wrong tie-breaker.

Send six lines, get a valve that fits

Bore, end style, body build, grade, seat compound and standard. Give EFUN those six and we will confirm the head, the air supply and the face-to-face length before anything is quoted.

Check a specification

Standards And The Wall That Follows Them

EFUN builds six standard systems into the same valve: DIN, 3A, SMS, ISO/IDF, BS/RJT and ASME/BPE. The standard does not only change the ferrule profile. It changes the wall thickness behind it, and the wall is what a welder and a clamp actually see.

Nominal size SMS / ISO DS 3A RJT
2″ 50.8 × 1.5 50.8 × 1.45 50.8 × 1.65 51.05 × 1.725
6″ 152.4 × 2.8 152.4 × 2.2 152.4 × 2.8 152.4 × 2.2

Outside diameter and wall in millimetres, taken from the clamp-end body table for the same valve. At 2″ the four standards agree on the outside diameter to within a quarter of a millimetre and disagree on the wall by 0.275 mm. At 6″ the outside diameter is identical across all four and the wall swings between 2.2 and 2.8 mm.

Size a clamp on the outside diameter and the ferrule angle, and prepare a weld on the wall. A buyer who orders “2 inch clamp, sanitary” and receives 3A ferrules gets ferrules that fit the clamp and do not match the tube schedule welded last year — a mismatch of a quarter of a millimetre that stops a line. A valve that has to satisfy a 3A inspector must go on the order as 3A, with the 3A ferrule and the 3A wall. The word “sanitary” on a drawing carries no standard at all; for the difference between the six systems, see sanitary standards for butterfly valves.

Three Decisions On The Actuator

That settles the body. What remains is the head, and the three questions about it decide how the valve behaves when the plant loses air or power, or when someone cleans the line at two in the morning.

Drive: Air, Electric, Or Manual

EFUN builds all three for the same body, which makes this a process decision rather than a product decision.

Pneumatic is the default for hygienic on/off duty because it is fast, carries no electronics in the washdown zone, and fails to a known position without a battery. EFUN builds the pneumatic sanitary butterfly valve in three standards — normally closed, normally open and air to air — with a stainless head in Φ85, Φ108 and Φ133 (single acting, spring return, ambient −20 to 90 °C, air 0.2 to 0.8 MPa) or an aluminium ZT head in six sizes from ZT050D to ZT115D. Both take a solenoid and a feedback unit.

Electric earns its place where there is no instrument air, where the valve has to hold an intermediate position, or where you want a local indication of open and closed without running a feedback cable back to the panel. The HL-05, HL-10 and HL-20 heads carry an open/close lamp, a passive contact signal, in-head control and a 1k or 5k potentiometer, and cover DN20 to DN200 between them.

Manual is not a downgrade; it is the right answer for a valve that isolates a line twice a year. The pull handle comes in two sizes, and the multi-position handle in stainless or plastic covers DN10 to DN100 with 2, 3 or 4 detent positions, or 13 positions at 15° increments for throttling.

The mounting does not cross over. A handle fixes to the valve cover and stem with a single screw; an actuator sits on a bracket and bolts down. A body ordered for a handle cannot take a head without the bracket, and a body ordered for a head has no handle boss to fall back on.

Fail Position: Closed, Open, Or Air To Air

Three pneumatic standards exist, and the names describe what happens when the air disappears — which is the only moment the choice matters.

Standard On air failure Pick it for
Normally closed Spring returns the disc to shut Product isolation, CIP return lines, anything that must not pass on a trip
Normally open Spring returns the disc to open Tank vents, jacket cooling, relief paths that must stay open
Air to air Nothing. The disc stays where it stopped Divert duties that must hold position, throttling stations

Air to air is the deliberate absence of a fail position, chosen on a divert line where a valve snapping shut mid-transfer would be worse than a valve sitting still. What it needs is a plan: a receiver large enough to hold the actuator through a compressor trip, and a procedure for what the operator does when the air comes back.

The common mistake is ordering air to air because it is the cheapest head, on a line that loses air at the end of every shift. The valve stops wherever it was — often half open, with product sitting against the seat and the CIP circuit unable to reach either face.

Air Supply And Ambient Limits

The stainless head works between 0.2 and 0.8 MPa of air, with a 1.0 MPa maximum, in an ambient of −20 to 90 °C. Those four numbers are the whole specification, and each one has a failure mode attached.

Below 0.2 MPa the spring does not fully return the piston, so a normally closed valve closes to a few degrees off — enough to look shut and enough to leave the seat face outside the CIP spray pattern. Above 1.0 MPa the piston seals take a load they were not designed for and the head starts to leak at the vent. Above 90 °C ambient, which happens to any head mounted within a metre of an uninsulated steam line or a CIP supply, the seals harden and the spring rate drifts.

Two habits remove most of these faults. Take the air from a dried instrument header rather than a plant ring main, because condensate in a cylinder is what freezes a head on a cold morning. And write the supply pressure on the purchase order next to the head model, so the factory can confirm the spring against the pressure you actually run rather than the pressure in the catalogue.

Quick Picker: Bore To Actuator

Open the band that matches your line size. These are the standard heads for a butterfly body; a butterfly-type ball valve at the same bore takes a smaller head.

DN20 – DN65  ·  3/4″ – 2 1/2″

ZT050D covers 1″ to 1 1/4″ (DN20–DN32); ZT063D covers 1 1/2″ to 2 1/2″ (DN40–DN65). Both are aluminium, both take a solenoid and a feedback unit. Below 0.2 MPa the spring will not fully return.

DN80 – DN125  ·  3″ – 5″

ZT075D covers 3″ to 3 1/2″ (DN80); ZT088D covers 4″ to 5″ (DN100–DN125); ZT100D covers 5″ (DN125). Two heads share DN125, so the band alone does not fix the model — the body does.

DN150 – DN200  ·  6″ – 8″

The aluminium ZT series ends at ZT115D on DN150. From there the stainless Φ108 and Φ133 heads carry the range to DN200, and the electric HL-20 covers DN125–DN200 if there is no instrument air.

DN250 and above  ·  10″ – 24″

This band leaves the ZT and Φ families entirely. The flanged body takes NM heads: NM145S at DN250, NM160S at DN300, NM180S from DN350 to DN450, NM200S at DN500 and NM240S at DN600. Quote it as a separate line.

What To Write On The Purchase Order

Valves are rarely mis-ordered out of carelessness. The usual cause is six specifications compressed into a sentence with room for three, and the fix belongs in the form rather than the wording.

One Line Per Valve, Not A Paragraph

A paragraph invites the supplier to fill the gaps with whatever is on the shelf. A line with a column per specification leaves nothing to fill.

Qty Size End Standard Body Seat Actuator
6 DN50 Clamp SMS 316L EPDM ZT063D · NC · 24 VDC · 2 × PNP

Compare that with the line that arrives most often: “10 pcs sanitary butterfly valve 2 inch pneumatic”. Five choices are still open — clamp or weld, SMS or 3A, 304 or 316L, EPDM or FPM, NC or NO — and thirty-two combinations fit the sentence. The quotation comes back for one of them, and only occasionally the one on the drawing.

The order line should also carry the dimension the drawing does not: total height. A DN100 valve with a Φ133 head is taller than most people picture, and the place that shows up is the insulation jacket, three weeks after delivery.

Sanitary butterfly valve with a welded end on one side and a threaded end on the other

Actuator And Accessories As Separate Items

Put the head on its own line, under the valve, with its own model, its own function and its own accessories. Three reasons:

First, the head is the part you change. A line converted from manual to automated, or from pneumatic to electric, keeps its bodies and replaces its heads; if the head was buried inside a valve description, that change means a new part number and a new approval. Second, accessories have their own lead times and their own voltages. A 24 VDC solenoid and a 230 VAC solenoid are the same casting with different coils, and the coil is what arrives wrong. Third, a separate line makes the accessory list visible: solenoid, position feedback, silencer, and a manual override if the line has to be operable during an air failure.

The accessory list is short enough to write every time: solenoid valve with voltage and connection size, position feedback with signal type and number of switches, and an override if the duty needs one. Every item on that list matters. Leave one out and the factory assumes whatever is on the shelf.

Drawings And Documents To Request

Ask for four documents with the quotation, not after the order. Each one closes a gap that a catalogue cannot.

  • A dimensioned drawing with overall height, face-to-face length and the actuator envelope. Height decides whether the valve fits under the insulation; length decides whether the spool piece you already fabricated still fits.
  • A material certificate to EN 10204 3.1 for the wetted parts, if the line faces an audit. A 316L stamp on a drawing is a claim; the certificate is the evidence.
  • An FDA declaration for the elastomer, naming the compound on the order. A generic food-contact statement covering “silicone or EPDM” is not the same document.
  • The air connection drawing for the head: port size, solenoid interface and the position of the vent. This is the drawing the fitter reads on site, before he pipes it.

If the duty is pharmaceutical or export-bound, add the 3A or EHEDG certificate to that list and confirm it names the model, not the factory. A certificate for a family of valves is a marketing document; a certificate for the model on the order is a compliance document.

FAQ

Why does one actuator list two bore ranges?

Two columns, two valve families. A ZT050D covers 1″–1 1/4″ on a butterfly valve but only 3/4″–1″ on a butterfly-type ball valve, because the two bodies load the stem differently.

What does the electric actuator include?

On the HL-05, HL-10 and HL-20 heads: an open and closed position lamp, a passive contact signal for remote indication, in-head intelligent control, and a 1k or 5k potentiometer for position feedback.

Which handle fits a sanitary pneumatic butterfly valve?

None. A pneumatic body takes a bracket and bolts for the head, not a handle boss. The pull and multi-position handles fit the manual bodies, which share the disc and seat but not the mounting.

Does a bigger actuator always mean a bigger valve?

No. ZT088D and ZT100D both cover DN125, and the larger head exists because it also carries bigger bodies in other builds. Select on torque at your air pressure, then confirm the bore band.

What is the difference between a sanitary butterfly valve and a butterfly-type ball valve?

Both turn a quarter. The butterfly-type ball valve carries a full spherical seat for tighter shutoff and needs a smaller head at the same bore, so the two are never interchangeable on one order line.

Can the pneumatic head be swapped for an electric one later?

Yes, if the body left the factory with a bracket pattern that takes both. The body does not change; the head, bracket and coupling do. Ask for the mounting dimensions before you commit the order.

Conclusion

Six specifications, three actuator decisions, one line each on the order. The pattern that works is always the same: fix the bore against the actuator map rather than the catalogue page, fix the end style against whoever will open the valve, then fix the wall thickness against the standard the inspector will read. Seat compound and fail position are the two that come back to bite, because the process decides both and both are easy to leave at “standard”. Write them down. A correct purchase order is cheaper than a commissioning week.

Talk to a manufacturer who reads the specification

EFUN builds sanitary butterfly valves and pneumatic heads in Wenzhou, China, in 304 and 316L, to DIN, 3A, SMS, ISO/IDF, BS/RJT and ASME/BPE. Send a line size and a duty, and we will tell you which body and which head fit.

Start an enquiry

Related Resources

Why 3-Piece Sanitary Butterfly Valves Reduce Manual Cleaning Downtime

The maintenance argument for the three-piece body, measured in shutdown hours rather than part price.

How Does a Multi Position Handle Improve Sanitary Butterfly Valve Flow Control?

What the 15° detents actually buy you on a line that throttles, and when a head is the better answer.

What Are the Main Components of a Sanitary Butterfly Valve?

Body halves, disc, seat, bushings and stem seal, part by part — useful before specifying a spare-seat kit.

Coming next in this series

  • How to read an actuator torque table without a torque wrench
  • Why a CIP return line needs a normally closed valve, not a check valve
  • Face-to-face length: the dimension that decides whether a spool piece fits
RELATED NEWS
YOU MAY ALSO WANT TO SEE
GET A QUOTE
icon
icon